請問大大們....小弟看不懂這些步驟...有人可以教我嗎? 謝謝 |
尚未結案
|
worldone
一般會員 發表:3 回覆:5 積分:1 註冊:2003-11-21 發送簡訊給我 |
各位大大們好...小弟是Delihpi的初學者..
請問大大們....小弟看不懂這些步驟...有人可以教我嗎? 謝謝 小弟從第三步驟就開始不明白了 >"< 不好意思 英文沒學好 To install TurboPower LockBox into your IDE, take the following steps: 1. Unzip the release files into a directory (e.g., d:\lockbox). 2. Start Delphi or C Builder. 3. Add the source subdirectory (e.g., d:\lockbox\source) to the
IDE's library path. 4. Open & install the designtime package specific to the IDE being
used. The IDE should notify you the components have been
installed. a. For C Builder 6 and Delphi 6 or higher, install the VCL
design-time package (e.g., LxxxVDxx.*) when using LockBox
classes with VCL applications. b. For C Builder 6 and Delphi 6 or higher, install the CLX
design-time package (e.g., LxxxCDxx.*) when using LockBox
classes with CLX applications. 5. Make sure the PATH environmental variable contains the directory
in which the compiled packages (i.e., BPL or DPL files) were
placed.
|
P.D.
版主 發表:603 回覆:4038 積分:3874 註冊:2006-10-31 發送簡訊給我 |
引言: 各位大大們好...小弟是Delihpi的初學者.. 請問大大們....小弟看不懂這些步驟...有人可以教我嗎? 謝謝 小弟從第三步驟就開始不明白了 >"< 不好意思 英文沒學好 To install TurboPower LockBox into your IDE, take the following steps: 1. Unzip the release files into a directory (e.g., d:\lockbox). 解壓這些檔案到一個檔案夾, 如 d:\lockbox 2. Start Delphi or C Builder. 啟動 Delphi, 或 C Builder 3. Add the source subdirectory (e.g., d:\lockbox\source) to the IDE's library path. 將第1項的source路徑加入到Delphi中的 IDE Library 路徑中(在 Tools->Environment Options -> Library) 4. Open & install the designtime package specific to the IDE being used. The IDE should notify you the components have been installed. 把屬於設計階段(Designtime)的package加入到componment中 a. For C Builder 6 and Delphi 6 or higher, install the VCL design-time package (e.g., LxxxVDxx.*) when using LockBox classes with VCL applications. a.對於 C Builder6及Delphi 6或更高的版本, 你必須加入 LxxVDxx.* 類的package到 VCL中 b. For C Builder 6 and Delphi 6 or higher, install the CLX design-time package (e.g., LxxxCDxx.*) when using LockBox classes with CLX applications. b.對於 C Builder6及Delphi 6或更高的版本, 你必須加入 LxxxCDxx.*類的Package 到 CLX(所謂Clx 是 for Kylix) 5. Make sure the PATH environmental variable contains the directory in which the compiled packages (i.e., BPL or DPL files) were placed. 確認所有的上述package的路徑(path)都確實被連結到編譯的package大致是如此啦, 以上是英文教學~~~~, 真的要多加學習哦! |
Mummy
一般會員 發表:11 回覆:9 積分:4 註冊:2004-02-20 發送簡訊給我 |
請問我一直有以下錯誤出現??
有可能哪裡出錯??
我用C Builder 5.0 C Error] RSAKeys1.h(9): E2209 Unable to open include file 'LbAsym.hpp'
[C Error] RSAKeys1.h(10): E2209 Unable to open include file 'LbCipher.hpp'
[C Error] RSAKeys1.h(11): E2209 Unable to open include file 'LbClass.hpp'
.....
|
本站聲明 |
1. 本論壇為無營利行為之開放平台,所有文章都是由網友自行張貼,如牽涉到法律糾紛一切與本站無關。 2. 假如網友發表之內容涉及侵權,而損及您的利益,請立即通知版主刪除。 3. 請勿批評中華民國元首及政府或批評各政黨,是藍是綠本站無權干涉,但這裡不是政治性論壇! |